Portable Temperature Process Controller

Automated Aquarium Systems^™
Portable Temperature Process Controller

DATA SHEET:

The 986 Option portable housing allows use of either of these popular and powerful 1/4 DIN controls as a portable or bench top control. Designed for rugged use, the 986 option allows operation on any standard US 3-prong outlet.

Features

10 Amp 120 VAC outlet on front panel

On-off switch with pilot lamp

Combination jack for standard or mini size thermocouple plugs

Self storing 4 foot power cord

Optional alarm has audible signal with volume control

Specifications

Selectable Inputs: Thermocouple, RTD, DC Voltage, or DC Current selectable.
Input Impedance: Thermocouple = 3 megohms minimum. RTD current = 200 µA.
Current = 10 ohms. Voltage = 5000 ohms.
Sensor Break Protection: User determines control output to protect system after customer set time.
Set Point Range: Selectable (See Range Chart, previous page).
Display: Two 4 digit, 7 segment 0.30" high LEDs.
Control Action: Reverse (usually heating), Direct (usually cooling) selectable.
Proportional Band: 1 to 9999 °F, °C, or counts.
Reset Time (Integral): Off or 0.1 to 99.9 minutes.
Rate Time (Derivative): Off or 0.01 to 99.99 minutes.
Cycle Rate: 1 to 80 seconds.
On - Off Differential: Adjustable 1° F, 1° C, or 1 count to full scale in 1° F, 1° C, or 1 count steps.
Alarm On - Off Differential: 1° F, 1° C, or 1 count.
Fuzzy Intensity: 0 to 100%.
Fuzzy Rate: Off or 0.01 to 99.99 minutes.
Fuzzy Band: Off or 1 to 4000 °F, °C, or counts.
Accuracy: ±0.25% of span, ±1 least significant digit.
Resolution: 1 degree or 0.1 degree, selectable.
Line Voltage Stability: ±0.05% over the supply voltage range.
Temperature Stability: 4µV/°C (2.3 µV/°F) typical, 8 µV/°C (4.5 µV°F) maximum (100 ppm / °C typical,
200 ppm / °C maximum).
Common Mode Rejection: 140 db minimum at 60 Hz.
Normal Mode Rejection: 65 db typical, 60 db at 60 Hz.
Isolation: Relay and SSR outputs: 1500 VAC to all other inputs and outputs.
SP1 and SP2 Current outputs: 500 VAC to all other inputs and outputs, but not isolated from each other.
SP1 and SP2 Switched Voltage outputs: 500 VAC to all other inputs and outputs, but not isolated from each other.
Process Output (Options 934, 936): 500 VAC to all other inputs and outputs.
Supply Voltage: 100 to 240 VAC, nominal., +10 -15%, 50 to 400 Hz. single phase; 132 to 240 VDC, nominal., +10 -20%.
Power Consumption: 5VA maximum.
Operating Temperature: -10 to +55 °C (+14 to 131 °F).
Storage Temperature: -40 to +80 °C (-40 to 176 °F).
Humidity Conditions: 0 to 90% up to 40 °C non-condensing 10 to 50% at 55 °C non-condensing.
Memory Backup: Nonvolatile memory. No batteries required.
Control Output Ratings:
SSR: 2.0 A combined outputs A & B @ 240 VAC at 25 °C (77°F). Derates to 1.0 A @ 55° C (130°F).
Relay: SPDT, 3 A @ 240 VAC resistive; 1.5 A @ 240 VAC inductive;Pilot Duty Rating: 250 VA, 2 A
@ 120 VAC or 1 A @ 240 VAC.
Alarm Relay: SPST, 3 A @ 240 VAC resistive; 1.5 A @ 240 VAC inductive; Pilot Duty Rating: 240
VA, 2 A @ 120 VAC or 1 A @ 240 VAC.
Current (isolated): 0 to 20 mA across 600 ohms maximum.
Switched Voltage (isolated): 15 VDC @ 20 mA.
Panel Cutout: 45 mm x 45 mm (1.775" x 1.775").
Depth Behind Mounting Surface: 115.3 mm (4.54").
Weight: 227 g (8 oz).
Agency Approvals: Pending.
Front Panel Rating: Type 4X, (IP65).

Input Ranges

Specify by Order Code

INPUT TYPE		RANGE	Order Code
T/C,	J*, Iron/Constantan	-100 to 1600° F -73 to 871° C	986/J
T/C,	K*	-200 to 2500° F -129 to 1371° C	986/K
RTD,	100 Ohm Platinum, 0.00392 Ohms/Ohm/°C*	-328 to 1607° F -200 to 875° C	986/RTD
RTD,	120 Ohm Nickel, 0.006725 Ohms/Ohm/°C*	-112 to 608° F -80 to 320° C	986/RTD
RTD,	100 Ohm Platinum, 0.00385 Ohms/Ohm/°C*	-328 to 1607° F -200 to 875° C	986/RTD

* These Input Types can be set for 0.1° display. If temperature goes above 999.9° or less than -199.9° the display will return to whole degree resolution.

How To Order

Specify part number from chart below:

Features	Using 2500 Series	Using 2600 Series
Single Set Point, Type J	25013-986/J	26030-986/J
Single Set Point, Type K	25013-986/K	26030-986/K
Single Set Point, 3-Wire RTD	25023-986/RTD	26030-986/RTD
Single Set Point with Alarm, Type J	25113-986/J	26130-986/J
Single Set Point with Alarm, Type K	25113-986/K	26130-986/K
Single Set Point with Alarm, 3-Wire RTD	25123-986/RTD	26130-986/RTD
Dual Set Point, Type J	Not Available	26033-986/J
Dual Set Point, Type K	Not Available	26033-986/K
Dual Set Point, Type 3-Wire RTD	Not Available	26033-986/RTD
Dual Set Point with Alarm, Type J	Not Available	26133-986/J
Dual Set Point with Alarm, Type K	Not Available	26133-986/K
Dual Set Point with Alarm, 3-Wire RTD	Not Available	26133-986/RTD

HOW TO ORDER:

25013-986/J: Portable Temperature Process Controller, Single Set Point, Type-J, 10A 120VAC Outlet...$500.00

986 Series Instruction and Operation Manual

ACCESSORIES:

461-0004: 30Amp Fuse...$60.00

How To Place your ORDER